The Manualmaniac™ MultiLift Pro is designed to temporarily lift, hold and position cabinets, doors, panels, tiles, boards and other workpieces during installation or assembly.

The two-jack system is especially useful when both sides of a workpiece need to be raised gradually and kept at a similar height. It can help with upper and base cabinet installation, door alignment, panel positioning, tile support, shelving and workshop assembly.

It is a rigid positioning tool, not a flexible support. Both jacks must stand on flat, stable surfaces with the load centred on their contact points. The workpiece must be permanently fastened or independently supported before the jacks are removed.

Each MultiLift Pro has an adjustable working range of approximately 38–60 cm / 14.96–23.62 in. The listed maximum extension is 23.4 in / 59.4 cm. The body is approximately 16 in tall, and the base measures approximately 3.7 × 4.1 in.

The load limit depends on how the jacks are configured:

• Direct lifting mode: up to 360 lb / 163 kg per pair
• Extended cabinet-support mode: up to 180 lb / 81.6 kg per pair

These figures apply to the pair, not to each individual jack. Never use the higher 360 lb rating while the jacks are in the extended cabinet-support configuration. Uneven loading, unstable surfaces and side pressure can significantly reduce stability.

Start by placing both jacks on a clean, flat and stable working surface. Position one near each side of the cabinet or workpiece so the weight is distributed between them. Select the appropriate contact attachment and make sure every part is seated securely.

Raise the load in small steps, alternating between the left and right jack. Do not raise one side all the way before adjusting the other. Watch the scale markings and regularly check the workpiece with a spirit level.

Once the required height and alignment are reached, install any necessary shims and fasten the workpiece to suitable structural supports according to its manufacturer’s instructions. Confirm that it is independently secured before unloading or removing either jack.

The paired supports can make solo installation more manageable because they hold the cabinet at working height while you check its position and install the fasteners. This keeps both hands available for measuring, levelling and fastening instead of physically holding the cabinet.

However, the MultiLift Pro does not replace safe lifting practices. You must still place the cabinet onto the supports safely. Large, heavy or awkward cabinets may require another person or suitable lifting equipment.

The jacks also do not replace correct wall anchors, mounting rails or structural fasteners. If the cabinet weight, installation height or site conditions make solo handling unsafe, use additional help.

Your order includes a complete two-jack support system:

• 2 × MultiLift Pro cabinet jack assemblies
• 2 × steel support base plates
• 2 × detachable top clips
• 3 × plastic foot-pad components: one main platform and two smaller inserts

The interchangeable components allow the supports to be configured for different positioning and contact tasks. Before use, inspect all parts and make sure the selected attachment is installed correctly and remains fully engaged under the load.

Choose the attachment according to the shape, material and position of the workpiece. The broad steel plates provide a stable contact area for general lifting and support. The detachable top clips help with positioning or holding suitable edges and panels. The plastic foot-pad components can provide a less aggressive contact surface for appropriate finished materials.

Always inspect the attachment and workpiece before applying pressure. Remove dust, metal chips and debris that could scratch the surface. For delicate, polished or easily marked materials, place a clean non-slip protective layer between the contact point and the workpiece and test it first in an inconspicuous area.

Surface protection depends on the material, finish, load and cleanliness of the contact points, so completely mark-free use cannot be guaranteed on every surface.

First, verify that the cabinet or workpiece has been permanently fastened or is supported by another independent method. Never release a jack while it is the only thing preventing the load from falling.

Keep fingers and hands away from the mechanism, contact plates and other pinch points. Maintain control of the workpiece and operate the release gradually. Lower each side in small alternating steps so the load remains balanced.

Do not abruptly release a loaded jack or allow the workpiece to lean sideways. After the pressure has been removed, take out both jacks and check that all permanent fasteners remain secure.

Yes. The MultiLift Pro is intended only for temporary lifting, alignment and positioning during installation or assembly.

Do not use it as permanent structural support, scaffolding, a vehicle jack, overhead safety equipment or a substitute for approved shoring. Never work, stand or place any part of your body beneath a load supported only by these jacks.

Do not exceed the rating for the selected configuration, join multiple jacks together to increase their height, use them on sloped or unstable surfaces, or apply strong sideways force. Inspect both jacks before every use and stop immediately if any rail, lever, spring, base or attachment appears bent, cracked, loose or damaged.

Standard delivery usually takes 7–14 business days after the order has been dispatched. Priority delivery usually takes 5–10 business days after dispatch. Order processing time is separate from the estimated delivery window, and delivery dates may be affected by customs, local carriers or circumstances outside our control.

You may request a return within 30 days after receiving your order. The product must be unused, undamaged and returned with all components and its original packaging. Contact our support team before sending anything back, as returns sent without prior authorization may not be accepted.